Hook up subwoofers to factory radio

hook up subwoofers to factory radio

Can I add a subwoofer to my factory stereo?

Adding a subwoofer to your factory stereo is a great way to improve your sound without giving up your familiar factory controls. In this video, you can follow along as one of our experts installs an amplifier and subwoofer in a car with a factory stereo. Youll see all the basics of amplifier installation, including:

Where to tap into speaker wire for subwoofer?

Generally if tapping into factory wires for a subwoofer, its best to tap into the rear speaker leads. This mainly comes into play if an aftermarket radio is installed and a high pass filter is set on the front speakers to eliminate some of the bass from the front of the vehicle and of course this would take those lower frequencies away from ...

What is a powered subwoofer and how does it work?

Powered subwoofers consist of an integrated amplifier, speaker driver and a modified enclosure for a powered subwoofer. This unique combination ensures that you will only listen to neat bass. In this article, our editors have explained in detail about Installing a powered subwoofer to a factory stereo.

How do you hook up speakers to the radio?

We grounded to a seat bolt right here back by the amplifier, and then we grabbed speaker wire signal from the factory radio in the dash, connected that to a line output converter right behind the radio, and ran RCA cables and our blue remote turn on wire from behind the radio, down the drivers side of the vehicle, right back here to our amplifier.

Can you add a subwoofer to a factory car stereo?

Adding a subwoofer to a factory stereo is an excellent method to boost your sound while retaining your factory controls. The nifty devices can produce bass and sub-bass sounds at low frequencies. Thankfully, it’s pretty simple to wire one into an existing car stereo system. Do note that subwoofers can be quite energy-consuming.

How do I hook up a subwoofer to a receiver?

The subwoofer is hooked up to the receiver with a single interconnect cable. Stereo receivers, pre-amps, and integrated amplifiers rarely have subwoofer output jacks or offer bass-management options.

What is a powered subwoofer and how does it work?

Powered subwoofers consist of an integrated amplifier, speaker driver and a modified enclosure for a powered subwoofer. This unique combination ensures that you will only listen to neat bass. In this article, our editors have explained in detail about Installing a powered subwoofer to a factory stereo.

Do subwoofers affect sound quality in a car?

You won’t get the exact same sound quality from your subwoofers as you would if you had an aftermarket stereo (like Alpine or Kenwood) in your car. The reason is that you’re not enhancing the voltage of the stereo, and therefore aren’t giving it the proper “juice”.

What is the difference between an active subwoofer and a passive subwoofer? A subwoofer (sub) is speaker, that is dedicated to the reproduction of low-pitched audio frequencies most commonly referred to as bass. Passive subs are called passive because they need to be powered by an external amplifier or Audio/Video (A/V) receiver .

How do you hook up speakers to a receiver?

To hook up speakers, you just connect the speaker wires to the appropriate outlets on the A/V receiver. Before you plug and play, though, there are a few points to remember. Keep your speakers in phase. Each speaker wire consists of two conductors, a positive and a negative.

What wire do you connect speaker wires to?

For the woofer, midrange and tweeter speakers, connect all three of their black wires to the output E, and then the woofer red to W, midrage red to M, and the tweeter red to T. Thanks! How can I tell which speaker wire is positive?

What is the best way to twist speaker wires?

Speaker wires are most commonly found as bare, meaning that you would use a wire stripper to expose the strands at the ends. Its good to twist the bare wire strands tightly so that they stay together as a neat single twisted wire, no matter if your equipment uses spring clips or binding posts.

How do I connect wires to my amplifier?

Others have a row of little sockets for you to connect wires to. It should match a row of sockets on the back of your amplifier which looks something like this: Insert the wires into the corresponding sockets. It is important to keep things consistent throughout this step on a couple of different levels.

Related posts: